Metal Satin Finish Acrylic Stainless Steel Lower Carbon Paint Supercoat-316L BULK

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

SuperCoat-316L Bulk is ready to use, low carbon stainless steel paint for new and painted metal surfaces. Why 316L low carbon stainless steel pigmented paint drys as a satin gloss finish when cured, protection from all types of weather, chemical fumes and spillage, and spillage of oil or water.

Get Local Price Information Now

Clear
  • Description

    Metal Satin Finish Acrylic Stainless Steel Lower Carbon Coating

    Metal Satin Finish Acrylic Stainless Steel Lower Carbon Coating

    Acrylic resin, pigmented with 100% 316L grade stainless steel.  Use wherever you need maximum corrosion resistance, as well as protection from all types of weather.  Resists chemical fumes and spillage, and spillage of oil or water.  Apply to properly prepared new or unpainted galvanized metal, aluminum, tin, mild steel, or masonry surfaces.  Available in metallic gray and can be used for touch up on all stainless coatings. General use on metals.

    How to Apply SuperCoat-316L on Metal:

    Only Apply SuperCoat 316L when air and surface temperatures are between 50oF and 100oF and surface temperature is at least 5oF above the dew point.
    Preparing the Metal Surface for 316L Stainless Steel Pigmented paint:

    New metal surfaces should be free of oil, grease, rust or other contaminants. For best results, commercial sandblast surfaces before priming provides “tooth” for the coating to get maximum adhesion. Old painted surfaces should be free of grease, oil, rust, chalk and loose peeling paint, then apply Supercoat-316L  directly to the painted surface.

    SuperCoat 316L Appearance: Satin Gloss finish
    Recommended Metal Primer: Steel Plus Epoxy Primer

    How to Thin SuperCoat 316L:

    Using a Roller or Brush: Thinning usually is not required.  Use 5%-10% if needed (approximately ½ (Paint Thinner) per gallon).
    Using an Air Atomizer Sprayer: Use 10%-20% or as needed (approximately 1 ½ pints per gallon). (Paint Thinner)
    Using an Airless Sprayer: Normally not required, use 5%-10% if required (approximately ½ pint per (Paint Thinner)  gallon).
    Dura-Steel OC 316™ CleanUp: Paint Thinner

    Recommended Equipment for SureCoat 316L™ Paint:

    Brush: Use a quality synthetic bristle brush
    Roller: Use good quality natural or synthetic cover.
    Air Atomized Spraying: Follow equipment manufacturers nozzle and needle selection recommendation for use with medium viscosity paints.
    Airless Spraying: Use .011 to .013 tip at 2000 to 2500 psi.
    Hot Spray: Recommended temperature 120°F  to 140°F

    SureCoat 316L Bulk™ Specifications:

    Weight Per Gallon:  9.4 Lbs
    Solids by Weight: 64.5%
    Solids by Volume: 43%
    Recommended: DFT: 2 mils
    WFT to Achieve: DFT 5 mils
    Theoretical Coverage: @1 MIL DFT 688 sq. ft./gal
    Actual Coverage at Recommended DFT: 300 sq. ft./gal  (Assumes 15% material loss)

    Dry Time @70F – 80F and 50% Humidity:
    Tack Free: 15 minutes
    Handle: 1 hour
    Recoat: 24 Hours
    Full Cure: 2 days (drying can be accelerated)
    Heat Resistance When Fully Cured: 250F
    Shelf-Life: 2 years

    Safty Information for Metal Epoxy Stainless Steel Primer:

    VOC: 5.37 lbs. per gallon or 643 grams per liter.
    Flash Point: 45F

    FLAMMABLE LIQUID AND VAPOR.  Vapor is harmful.  Keep away from heat and open flame.  Use only with adequate ventilation.  Avoid prolonged breathing of vapor or spray mist.  Avoid prolonged or repeated contact with skin.  Do not take internally.

     For specific information refer to the Safety Data Sheet.

    *** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***


    SuperCoat-316L Bulk™ Ordering Information:

    SizeWt./CaseCase Quantity
    21-0316-011 Gallon404
    21-0316-055 Gallons501
  • Supercoat-316L Bulk Request



    Name:*
    E-mail:*
    Phone:
    -
    Location:*
    Your Role:*
    Your Request:
    Bot Check:
    Metal Satin Finish Acrylic Stainless Steel Lower Carbon Paint Supercoat-316L BULK

    Metal Satin Finish Acrylic Stainless Steel Lower Carbon Paint Supercoat-316L BULK

  • WEIGHT PER GALLON 9.4 lbs.
    SOLIDS BY WEIGHT 64.5%
    SOLIDS BY VOLUME 43%
    RECOMMENDED DFT 2 mils

    WET FILM TO ACHIEVE DFT 5 mils

    THEORETICAL COVERAGE
    @ 1 Mil DFT 688 sq. ft./gallon
    PRACTICAL COVERAGE 300 sq. ft./gallon
    @ RECOMMENDED DFT
    (Assumes 15% material loss)
    DRY TIMES @ 70F – 80F Tack Free 15 minutes
    (21 – 27C) AND 50% RH Handle 1 hours
    Recoat 24 hours Fully Cured 2 days (rate can be accelerated)

    DRY HEAT RESISTANCE 250 F
    SHELF LIFE 2 years

  • Additional information

    Size

    1 Gallon, 5 Gallons

  • Share your thoughts!

    5 out of 5 stars

    1 review

    Let us know what you think...

    What others are saying

    1. admin

      5 out of 5 Metal Satin Finish Acrylic Stainless Steel Lower Carbon Paint

      Admin admin

      ow carbon stainless steel paint for new and painted metal surfaces.

      (0) (0)

      Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

    2. admin

      Metal Satin Finish Acrylic Stainless Steel Lower Carbon Paint Supercoat-316L BULK

      Admin admin

      SuperCoat-316L Bulk is ready to use, low carbon stainless steel paint for new and painted metal surfaces. Why 316L low carbon stainless steel pigmented paint drys as a satin gloss finish when cured, protection from all types of weather, chemical fumes and spillage, and spillage of oil or water.

      (0) (0)

      Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

    ×

    Login

    Register

    Continue as a Guest

    Don't have an account? Sign Up