High Gloss Chemical Resistant Non Yellowing Novolac Based Epoxy White / Clear – Steel Plus CE

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

Steel Plus CE is water-based, non-yellowing, 100% Novolac based epoxy available in clear and white finishes. CE  Epoxy is chemical and corrosion resistance with a low odor ideal for commercial application where workers are present without causing downtime. Steel Plus Epoxy is an accepted USDA and FDA epoxy product.

Get Local Price Information Now

Clear
  • Description

    Chemical Resistant Non Yellowing Novolac Based Epoxy White / Clear - Steel Plus CE

    Chemical Resistant Non-Yellowing Novolac Based Epoxy White / Clear – Steel Plus CE

    Steel Plus CE White and Clear are very high quality, water-based epoxy paints that are cured with an aliphatic amine curing agent for the utmost in chemical and corrosion resistance. The clear is designed to be used over Steel Plus CE-316 to offer an additional coat of high gloss protection or to be used alone as a clear finish. The white is used in place of the stainless steel finish where USDA White is required.

    These high gloss enamels are two-component, water-based, non-yellowing, 100% Novolac based epoxies. They contain no HAP solvents, have exceptionally fast dry and are cured with a cycloaliphatic amine curing agent. They are a 2 to 1 mix that requires no induction time and has the exceptional chemical and corrosion resistance expected from a Novolac epoxy. Their low odor makes them ideal to use in a warehouse or manufacturing plant while workers are present. They are very low VOC, are easy to apply, with water clean up and are USDA and FDA accepted.

    Uses for Steel Plus CE: Epoxy  A tough, heavy duty, extremely chemical resistant epoxy designed for maximum performance in severe environments.

    Available Appearances: High Gloss Clear and High Gloss White

    Required Curing Agent: 16-CURE; mixing ratio (2) parts “A” + (1) part “B” by volume

    Recommended Primers: In most cases, Steel Plus CE is used over a stainless steel middle-coat. Steel Plus Epoxy Primer or Prime Solution 5250 Red/5253 Gray.

    Surface Preparation for Chemical Resistant Epoxy Paints:

    Required on all metal or old coatings: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with BC-4000 cleaner or another suitable cleaner. Thoroughly cured old coatings or new smooth metal may require scuff sanding for maximum adhesion.
    Moderate Exposure: Abrasive blast the surface to SSPC-SP-6 commercial blast before priming.
    Severe Exposure: Abrasive blast the surface to SSPC-SP-10 near white blast before priming.

    How to Apply Chemical and Corrosion resistant Epoxy Paints:

    Apply only when air and surface temperatures are between 50oF and 100oF and surface temperature is at least 5oF above the dew point.

    Thinning Epoxy Steel Plus CE Coating:

    Using Roller or a Brush: Use as mixed. Dilute with water as needed.
    Using an Air Atomized Sprayer: Dilute up to 5-10% with water if needed.
    Using an Airless Sprayer: Normally, no dilution needed.
    Steel Plus CE Clean Up: Use soap and water

    Recommended Equipment to Use when Applying Steel Plus CE High Gloss Epoxy:

    Filter: Use 100 mesh stainless steel screen or nylon bag when needed
    Brush: Use a quality synthetic bristle brush
    Roller: Use quality roller cover
    Air Atomized Sprayer: Please follow the equipment manufacturers nozzle and needle selection recommendation for use with medium viscosity paints. Spray at 45-60 psi.
    Airless Sprayer: 1800-2400 psi with 0.011-0.013 tip
    Hot Spraying Temperature: 120oF

    Specifications of Steel Plus Non-Yellowing Novolac Based Epoxy:

    Weight Per Gallon: 8.70 Lbs
    Solids by Weight: 26.51%
    Solids by Volume: 23.52% (part “A” alone), 30.98% (part “A” & “B” combined)
    Recommended DFT: 2.5 mils.
    WFT to Achieve DFT: 8.0 mils.
    Induction Time: None
    Theoretical Coverage:  @1 MIL DFT 495 sq. ft./gal
    Actual Coverage ar recommended DFT: 198 sq. ft./gal
    Dry Time @77F  and50% Humidity: Tack Free: 20-60 minutes
    Handle: 2-4 hour
    Recoat: 1 hour after dry to touch
    Full Cure: 7 days (drying can be accelerated)
    Pot Life: 2 hours (mix just enough paint to use up in 2 hours)
    Heat Resistant when fully cured:  300F
    Shelf Life: 1 year

    Important Safety Information for Steel Plus CE High Gloss  Novolac Based Epoxy

    VOC: 188 g/L, or 1.57 Lbs/gal (part “A” & “B” combined)
    Flash Point: N/A

    Warning: California Prop. 65 warning: Detectable amounts of chemicals known to the state of California to cause cancer, birth defects or other reproductive harm, may be found in this product or its vapors. For specific information refer to the Safety Data Sheet(SDS).

    *** FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF CHILDREN. ***


    Novolac Based Epoxy White and Clear Steel Plus CE Ordering Information:


    Steel Plus CE (Clear)

    Product Number Size Wt./Case Case Quantity
    20-450A-F4 1 Quart 16 6
    20-450A-F1 1 Gallon 36 4
    20-450A-F5 5 Gallons 48 1

    Steel Plus CE (White)

    Product Number Size Wt./Case Case Quantity
    20-809A-F4 1 Quart 14 6
    20-809-F1 1 Gallon 36 4
    20-809A-F5 5 Gallons 48 1

     

    Please Note: This product needs a curing agent.  If you order 1 Gallon you will need Qty. 2   16-Cure-F4 (Quart), If you order 5-Gallon pail you will need Qty. 2 16-Cure-F1 (Gallon) and Qty. 2  16-Cure-F4 (Quart) and if you order Quart you will need Qty. 2  16-Cure-8 (1/2 Pint).

  • Steel Plus CE Request



    Name:*
    E-mail:*
    Phone:
    -
    Location:*
    Your Role:*
    Your Request:
    Bot Check:
    High Gloss Chemical Resistant Non Yellowing Novolac Based Epoxy White and Clear - Steel Plus CE

    High Gloss Chemical Resistant Non-Yellowing Novolac Based Epoxy White and Clear – Steel Plus CE. Steel Plus CE

  • WEIGHT PER GALLON 8.70 Lbs
    SOLIDS BY WEIGHT 26.51%
    SOLIDS BY VOLUME 23.52% (part “A” alone), 30.98% (part “A” & “B” combined)
    RECOMMENDED DFT 2.5 mils
    WFT TO ACHIEVE DFT 8.0 mils
    INDUCTION TIME None
    THEORETICAL COVERAGE @1 MIL DFT 495 sq. ft./gal
    ACTUAL COVERAGE AT RECOMMENDED DFT 198 sq. ft./gal
    DRY TIME @77OF
    AND 50% HUMIDITY Tack Free: 20-60 minutes
    Handle: 2-4 hour
    Recoat: 1 hour after dry to touch
    Full Cure: 7 days (drying can be accelerated)
    POT-LIFE 2 hours (mix just enough paint to use up in 2 hours)
    HEAT RESISTANCE
    OF CURED FILM 300oF
    SHELF-LIFE 1 year

  • Additional information

    Size

    1 Quart, 1 Gallon, 5 Gallons

    Color

    Clear, White

  • Share your thoughts!

    5 out of 5 stars

    1 review

    Let us know what you think...

    0 reviews with a 2-star rating

    There are no reviews with a 2-star rating yet

    ×

    Login

    Register

    Continue as a Guest

    Don't have an account? Sign Up